Nammu-Tech UK
Stage Rigging Kit
Stage Rigging Kit
For none UK orders VAT not included, see shipping page for more info
Couldn't load pickup availability
The Nammu Tech Stage Rigging Kit is a lightweight, streamlined, and travel-friendly solution for rigging stage or deco cylinders—no tools required.
Designed to fit any cylinder from 5L to 15L, this tool-less setup offers durability and ease of use without compromising performance.
Just pick your desired colour and size!
Kit includes:
-
✅ A set of colour-matched cylinder hose tidies for clean, snag-free hose management
-
✅ One 25mm cam band for secure, adjustable cylinder attachment
-
✅ Two 120mm 316 stainless steel bolt snaps – corrosion-resistant and dive-proven
-
✅ Two lengths of Type 4 Paracord in matching colour:
-
30cm for the cam band
-
50cm for the cylinder neck
-
Whether you're diving locally or flying out for a tech trip, this kit packs small, weighs next to nothing, and sets up in minutes—no tools, no hassle. Engineered for reliability in cold water, overhead environments, and open water alike.
Buying the stage kit is 30% cheaper than buying the individual components.
Share
Até a presente data não foi entregue os produtos.
Preciso de localizador da compra e quando receber os produtos poderei fazer a avaliação.
My item shipped from Royal Mail has still not arrived in Saudi Arabia. Royal Mail last reported 6MAY as departing LANGLEY HWDC.. Saudi Parcel Service shows the Item has not arrived at LANGLEY HWDC.
I'm afraid this is disposable equipment.
1. Unfortunately, the cylinder cam band is so weak and flimsy that while it might still hold up to handling in the water, it could break when carried on land.
2. Hose holders ("Cylinder hose tidy") - suitable for hoses around 12 mm thick (LP HDR). Thicker hoses - old Aqualung, Apeks, or Poseidon - won't even fit through the holes!
3. Be careful with the Miflex - they will slip. Unless they get damaged and shredded, the plastic from the hose will cut your hands or make a hole in your drysuit (soft trilam).
THESE ACCESSORIES SHOULD NOT BE 3D PRINTED!! THE CYLINDER CLAMP (CAM BAND) SHOULD BE STRONGER AND THE HOSE HOLDER (Hose Tidy) MADE OF RUBBER!
Obawiam się, że to jest sprzęt jednorazowy.
1. Niestety zapięcie obręczy butli ("Cylinder cam band") jest tak słabe, cienkie, że o ile manipulowanie butlą w wodzie może jeszcze wytrzymać, to przy przenoszeniu na lądzie może pęknąć.
2. Uchwyty do węży ("Cylinder hose tidy") - nadają się do węży o grubości około 12 mm (lp hdr). Węże grubsze - stary aqualung, apeks czy poseidon - nawet się nie zmieszczą do otworów!
3. Uwaga na miflex - będą się przesuwać. O ile nie zniszczą się i nie poszarpią, po czym plastik z węża pokaleczy dłonie lub zrobi dziurę w suchym skafandrze (soft trilam)
TE AKCESORIA NIE POWINNY BYĆ DRUKOWANE NA DRUKARCE 3D!!
ZAPIĘCIE BUTLI (cam band) POWINNO BYĆ MOCNIEJSZE A UCHWYTY WĘŻY (hose tidy) Z GUMY!!!
Didn’t get 3 of my bolt snaps
I am asking Nammu tec to send detailed instructions on how to “don” or correctly set the knots at the end of each bungee. The (2) hose donning fixture that bungees around the tank does not have proper recess to provide a flush fit to the tank. The fixtures for donning the hises do NOT have an opening in the center as shown in some of the videos AND the current fixtures do not have a deep enough recess to allow the knots to be pulled in so that the entire fixture will sit flush with the OD of the tank